Technical Data




ConfiAd Cartridge type is a two-component based on acrylic resin for bonding of solid surfaces and engineered stones. Combined at a 10:1 ratio, it has a working time of 11 to 16 minutes and fixture time of 22 to 30 minutes.ConfiAd Cartridge type is available in off-white and is supplied in ready to 50ml, 75ml, 250ml, 490ml cartridges as a non-sagging gel.





  • - Can be stressed very quickly due to it’s high initial stability
  • - Very rapid hardening and solvent free type
  • - Easy measuring and mixing by use of cartridge system
  • - Excellent adhesion on solid surfaces and engineered stones-
  • - Working Time (22 °C) : 11 ~ 16 min                
  • - Fixture Time (22 °C)  : 22 ~ 30 min
  • - Operating Temperature : max 120℃
  • - Gap Filling : 3 mm
  • - Mixed Density  : 1.20 g/cc
  • - Flash Point : 10 °C



Physical Properties (uncured) -  Room Temperature 





Viscosity, cPs, 23℃  






Density, g/cc    



Mix Ratio by Volume  



Mix Ratio by Weight  



Recommended Type

Cartridge (75ml / 250ml)


Mechanical Properties (Cured) - Room  


                          Bending Strength   
                                      Strength, psi                               3,200  
                                      Strength, kg/
㎠                             220

Typical Exotherm Curve for
ConfiAd Cartridge type at 22 °C (50 grams)



Handling and Application


ConfiAd Cartridge type is flammable and can be dangerous if used improperly. Keep containers closed after use. Wear gloves and safety glasses to avoid skin and eye contact. Wash with soap and water after skin contact. In case of eye contact, flush with water for 15 minutes and get medical attention. Harmful if swallowed. Keep out of reach of children. Keep away from heat, sparks, and open flames. Reference the Material Safety Data Sheet (MSDS) for more complete safety information.

※ Note

Because of the rapid curing features of this product, large amounts of heat are generated when large masses of material are mixed at one time. The heat generated by the exotherm resulting from the mixing of large masses of adhesive can result in the release of entrapped air, steam, and volatile gases. To prevent this, use only enough material as needed for use within the working time for the product and confine gap thickness to no more than 3mm.



Dispensing Adhesive


ConfiAd Cartridge type may be applied manually or with automated equipment. 
 Static mixer selection is critical to the proper mixing and performance of adhesives.
 To assure maximum bond strength, sheets must be mated within the specified working time.
 Use sufficient material to ensure the joint is completely filled when parts are mated and clamped.  All adhesive application, part positioning, and fixturing should occur before the working time of the mix has expired.
 After indicated working time, parts must remain undisturbed until the fixture time is reached.
 Clean up is easiest before the adhesive has cured.





Application of adhesive at temperatures between 18℃ and 26℃ will ensure proper cure. Temperatures below 18℃ will slow cure speed and above 26℃ will increase cure speed.
The viscosities of COMPONENT A and B of this adhesive are affected by temperature.



  Storage and Shelf Life


Shelf life of ConfiAd Seamless Joint Adhesive is 2 years. 

Shelf life is based on continuous storage between 10℃ and 21℃.

Long term exposure above 26℃ will reduce the shelf life of these materials. Prolonged exposure of hardener above 40℃ quickly diminishes the reactivity of the product and should be avoided. Refrigeration is an acceptable means to increase shelf life,

For expiry date, please see the label.






1. Jin Gwang Industries Co., Ltd. strongly recommends that all substrates be tested with

          ConfiAd Cartridge type in the normal conditions to determine suitability.

2. Working Time: The time elapsed between the moment COMPONENT A and B of the
       adhesive system are combined  and thoroughly mixed and the time when the adhesive is
       no longer usable. Times presented were tested at 22℃.

3. Fixture Time: The interval of time after which surface being joined will support a 1 kg dead
       weight on a 12.7 mm overlap joint 25.4mm wide without movement. Times presented were 
       tested at 22℃.

4. Resistance to chemical exposure varies greatly based on several parameters
       including ;temperature, concentration, Bond line thickness, and duration of exposure.
       The chemical resistance listed assume long term exposures at ambient conditions.

5. In a typical bond line, exotherm temperatures will be lower than the temperatures shown.

6. The information provided, is based on laboratory testing under controlled conditions. It is the
       responsibility of the end  user to test the intended substrates under the conditions which
       they will be used, and to determine the suitability of the adhesive for the intended purpose.
       Jin Gwang Industries Co., Ltd. makes no representations or warranties of any kind

    concerning this data. Due to variance of storage, handling and application of these

    materials, can not accept liability for results obtained.